Version 7.2
619
Mediant 500 MSBR
User's Manual
31. Analog Gateway
31.13.3 Call Termination on FXO Devices
This section describes the device's call termination capabilities for its FXO interfaces:
Calls terminated by a PBX (see Call Termination by PBX on page 619)
Calls terminated before call establishment (see Call Termination before Call
Establishment on page 620)
Ring detection timeout (see Ring Detection Timeout on page 620)
31.13.3.1
Calls Termination by PBX
The FXO device supports various methods for identifying when a call has been terminated
by the PBX.
The PBX doesn't disconnect calls, but instead signals to the device that the call has been
disconnected using one of the following methods:
Detection of polarity reversal/current disconnect:
The call is immediately
disconnected after polarity reversal or current disconnect is detected on the Tel side
(assuming the PBX/CO generates this signal). This is the recommended method.
Relevant parameters: EnableReversalPolarity, EnableCurrentDisconnect,
CurrentDisconnectDuration, CurrentDisconnectDefaultThreshold, and
TimeToSampleAnalogLineVoltage.
Detection of Reorder, Busy, Dial, and Special Information Tone (SIT) tones:
The
call is immediately disconnected after a Reorder, Busy, Dial, or SIT tone is detected
on the Tel side (assuming the PBX / CO generates this tone). This method requires
the correct tone frequencies and cadence to be defined in the Call Progress Tones
file. If these frequencies are unknown, define them in the CPT file. The tone produced
by the PBX / CO must be recorded and its frequencies analyzed. This method is
slightly less reliable than the previous one.
Relevant parameters: DisconnectOnBusyTone and DisconnectOnDialTone.
Detection of silence:
The call is disconnected after silence is detected on both call
directions for a specific (configurable) amount of time. The call is not disconnected
immediately. Thus, use this method only as a backup option.
Relevant parameters: EnableSilenceDisconnect and FarEndDisconnectSilencePeriod.
Special DTMF code:
A digit pattern that when received from the Tel side, indicates to
the device to disconnect the call.
Relevant
ini
file parameter: TelDisconnectCode.
Interruption of RTP stream:
Relevant parameters: BrokenConnectionEventTimeout
and DisconnectOnBrokenConnection.
Note:
This method operates correctly only if silence suppression is not used.
Protocol-based termination of the call from the IP side
Note:
The implemented disconnect method must be supported by the CO or PBX.
Summary of Contents for Mediant 500 MSBR
