APRILIA RX 125 Service Station Manual Download Page 58

Page: 58 / 219

1. Instrument panel

2. Key switch

3. fuses

4. Battery

5. Voltage regulator

6. Generator

Recharge check

•

Start the engine and make it run at 6000 rpm.

•

Connect a tester in voltmeter function to check the direct current on the battery leads.

•

Turn on the low-beam lights.

•

The voltage must be between 13.5 and 15 V.

Troubleshooting

•

Check that the fuses are in good conditions.

•

Check the starter button.

•

Check the start-up relay.

•

Check the starter motor.

Control data

Flywheel check

•

Disconnect the alternator cable con-

nector.

•

Start the engine and make it run at

5000 rpm.

•

With the pocket tester measure the

voltage (alternating current) among the

three yellow cables. If the value indica-

ted by the tester is below 53 V, the

generator is faulty.

Standard off-load voltage: above 53 V (AC) at

6000 rpm.

Electrical system

RX SX 125

ELE SYS - 58

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands