APRILIA RX 125 Service Station Manual Download Page 189

Page: 189 / 219

TOTAL

•

Undo and remove both RAVE valve

screws and collect the locking wash-

ers.

•

Take out the exhaust valve unit from

the cylinder.

•

Disconnect the connector of the sys-

tem control unit.

•

Undo and remove both screws (8) from

the battery housing frame.

•

Remove the whole RAVE valve.

Checking

GASKETS

•

Check that the valve gasket (1) and the O-ring (2) (fitted to the valve seat) are not worn or

damaged.

EXHAUST VALVE

•

Clean off any combustion deposits from the exhaust valve (3) and from the valve duct in the

cylinder.

•

Make sure that the exhaust valve is not worn or damaged.

RX SX 125

Chassis

CHAS - 189

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands