APRILIA RX 125 Service Station Manual Download Page 126

Page: 126 / 219

Removing

•

Place the engine support so as to fa-

cilitate oil pump removal operations.

•

Undo and remove the two screws fixing

the oil pump.

•

Remove the oil pump and the O-ring

underneath; collect the oil pipes and

their guides.

Inspection

•

Male sure the delivery (1) and intake

(2) pipes do not leak or have pores at

their connecting points. Replace if re-

quired.

•

Clean the oil reservoir, the oil reservoir

filter and the oil intake pipe.

•

Always replace the oil pump when

damaged or leaking.

•

After installing the flexible pipe of the

oil pump, adjust it so that when in idle

position the marks on the pump lever

(3) are aligned with the pump (4) seat.

BLEEDING

Purge the oil pump and its pipes:

Engine

RX SX 125

ENG - 126

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands