APRILIA RX 125 Service Station Manual Download Page 167 | Manualshive

Page: 167 / 219

background image

13.12.2x22x2 Plain iron washer

14.M12 lower self-locking nut

15.TE flanged screw M6x20

16.Bushing

17.Clip M6

Adjusting

The rear shock absorber standard setting is adjusted to suit most low speed riding conditions, whether

the vehicle is partially or fully loaded.

However, this setting can be personalised to meet specific needs according to vehicle use.

CAUTION

ALLOW ENGINE AND SILENCER TO COOL OFF BEFORE OPERATING THE SET SCREWS.

THE SET NUT MUST NOT BE TIGHTEN OVER 25 mm (0.98 in) FROM THE BEGINNING OF THE
THREAD. IF SUCH DISTANCE IS EXCEEDED, THERE WILL BE SOME JERKING WHILE RIDING
EVEN ON SOME SLIGHTLY UNEVEN ROADS.

•

Operate on the set nut (1) (shock ab-

sorber spring preloading adjustment).

CAUTION

TURN THE SET NUT (1) GRADUALLY ONE TURN AT A
TIME.
TRY RIDING THE VEHICLE ON THE STREET UNTIL THE
OPTIMUM ADJUSTMENT IS OBTAINED.

REAR SHOCK ABSORBER ADJUSTMENT

Specification

Desc./Quantity

By tightening the set nut (1)

Spring (2) preloading increases

The scooter suspension is very hard.

Advisable for smooth or ordinary roads and when riding with

passenger.

By loosening the set nut (1)

Spring (2) preloading decreases

The vehicle suspension is very soft.

Advisable for uneven roads, without passengers.

RX SX 125

Suspensions

SUSP - 167

«
...
165
166
167
168
169
...
»

Summary of Contents for RX 125




























































































































































































































Reviews:

No comments

Related manuals for RX 125

Brand: KYMCO Pages: 69

Brand: Suzuki Pages: 311

Brand: Kabuto Pages: 20

Sixteenth Edition

Brand: MSF Pages: 60

Brand: URAL Motorcycles Pages: 104

Brand: Ops-Core Pages: 20

factor-x-rearset.gt

Brand: gilles.tooling Pages: 4

Brand: AGUSTA Pages: 427

Brand: VESPA Pages: 249

Brand: Shark Pages: 20

Brand: Bagster Pages: 2

Brand: RIEJU Pages: 49

Brand: ZTechnik Pages: 3

Brand: ZTechnik Pages: 5

SHERCO 250-300 SE/R

Brand: DEFYGRAVITY Pages: 67

Brand: Beta Pages: 196

Brand: Beta Pages: 360

Brand: Honda Pages: 185

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands