APRILIA RX 125 Service Station Manual Download Page 112

Page: 112 / 219

The piston nominal size is stamped on the piston crown.

Pistons are grouped in types according to their sizes:

•

PISTON "A"; Piston diam. = 53.98 mm (2.1252 in), wear limit = 53.93 (2.1232 in), matching

cylinder: "A" or "AB".

•

PISTON "B"; Piston diam. = 53.99 mm (2.1256 in), wear limit = 53.93 (2.1236 in), matching

cylinder: "B" or "AB".

•

PISTON "Oversize 1"; Piston diam. = 54.00 mm (2.1260 in), wear limit = 53.93 (2.1240 in),

matching cylinder: "B" or re-smoothed cylinder.

•

PISTON "Oversize 2"; Piston diam. = 54.00 mm (2.1264 in), wear limit = 53.93 (2.1244 in),

matching cylinder: re-smoothed cylinder.

Pistons are available with different types of piston rings which are identified with their part number:

•

PISTON (code 294583); chrome-plated PISTON RING (code 215670)

•

PISTON (code 294587); chromium-ceramic PISTON RING (code 215720)

•

PISTON (code 294589); chromium-ceramic PISTON RING (code 215820)

•

PISTON (code 294588); chromium-ceramic PISTON RING (new type) (code 215825)

IF A PISTON SHOWS SIGNS OF EXCESSIVE WEAR AS IT HAS BEEN FUNCTIONING WITH LOW
QUALITY FUEL (HIGH IN SULPHUR), USE CHROMIUM-CERAMIC RINGS AND CHANGE THE
FUEL BRAND USED.

Installing the cylinder head

•

Fit the O-ring in the cylinder groove.

•

Place the head.

•

Tighten in a star sequence the five

socket head screws fixing the head, to-

gether with the washers.

TIGHTEN THE FIXING NUTS AGAIN, WHEN THE ENGINE
IS COLD, AFTER THE FIRST 500 KM (310 MI).

Engine

RX SX 125

ENG - 112

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands