APRILIA RX 125 Service Station Manual Download Page 202

Page: 202 / 219

TURN INDICATORS

•

If necessary, remove the turn indica-

tors working from any side, then undo

and remove the screw and carefully

slide off the gauge with cables.

LICENSE PLATE LIGHT

•

If necessary, remove the license plate

light, undo and take out the screw and

carefully slide off the light with cables.

REAR LIGHT

•

If necessary remove the rear light, un-

do and take out both screws and collect

the washers.

•

Slide off the rear light with cables care-

fully.

Side body panels

CENTRAL FAIRING

The following operations refer to only one fair-

ing

but are valid for both.

•

Unscrew and remove the screw and

collect the collar.

Bodywork

RX SX 125

BODYW - 202

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands