APRILIA RX 125 Service Station Manual Download Page 178

Page: 178 / 219

•

The correct adjustment of the swing-

arm pin clearance is obtained by prop-

erly seating the ring nut set bushing (6)

and screwing it another 1 / 4 of a turn.

•

Firmly hold the bushing (6) and tighten

the ring nut (7) using a special tool.

Specific tooling

AP8101945

Fork pin ring nut

•

Now adjust the rear swingarm as fol-

lows:

- Loosen the pin (1), working from the left side.

- Working from the right side, fully loosen the ring

nut (6) with the specific box-spanner.

- Tighten the set bushing (6) to the prescribed tor-

que

- Use the specific box-spanner to tighten the ring

nut (7).

- Tighten the pin.

•

Tighten the chassis fixing screw (8) on

the engine.

Chassis

RX SX 125

CHAS - 178

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands