APRILIA RX 125 Service Station Manual Download Page 200

Page: 200 / 219

Seat

•

Place the vehicle on the service stand.

•

Insert the key in the lock.

•

Turn the key anticlockwise.

•

Lift and remove the saddle.

UPON REFITTING:
BEFORE LOWERING AND LOCKING THE SADDLE,
CHECK THAT THE KEY HAS NOT BEEN LEFT INSIDE THE
GLOVE-BOX / TOOLKIT COMPARTMENT.

•

Fit the saddle making sure to position

the corresponding rear hooks correct-

ly.

•

Lower and press the saddle to trip the

lock.

BEFORE RIDING, MAKE SURE THAT THE SADDLE IS
CORRECTLY LOCKED INTO POSITION.

Headlight assy.

•

Undo and remove both screws on the

upper plate.

•

Undo and remove the two screws fas-

tening the mudguard and collect the

nuts and washers from the bottom.

Bodywork

RX SX 125

BODYW - 200

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands