APRILIA RX 125 Service Station Manual Download Page 182 | Manualshive

Page: 182 / 219

background image

•

Move the vehicle forward so as to also check the chain vertical oscillation in other positions;

clearance should remain constant during all wheel rotation phases.

CAUTION

IF CLEARANCE IS GREATER AT SOME POSITIONS, THIS MEANS THAT SOME CHAIN LINKS
ARE FLATTENED OR JAMMED.
TO AVOID THE RISK OF SEIZURE, LUBRICATE THE CHAIN ON A REGULAR BASIS.

Adjust backlash if it is uniform but over or below 25

- 35 mm (0.99 -1.38 in), adjust it.

CAUTION

GET A SPECIFIC REAR SERVICE STAND (OPT) TO ADJUST THE CHAIN.

If chain tension needs adjusting after the check:

•

Place the scooter on its rear service

stand (OPT).

•

Loosen the nut (1) completely.

WHEEL CENTRING IS CARRIED OUT USING IDENTIFIA-
BLE FIXED REFERENCES (2-3) IN THE TENSIONER
MOUNTS ON THE SWING ARMS BEFORE THE WHEEL
PIN.

•

Loosen both lock nuts (4).

•

Actuate on the set screws (5) and ad-

just the chain backlash checking that

the references (2 - 3) match on both

sides of the vehicle.

•

Tighten both lock nuts (4).

•

Tighten the nut (1).

•

Wheel nut tightening torque (1):

Locking torques (N*m)

Rear wheel fixing pin

100

Chain sliders

CAUTION

FOR SPACE REASONS DETACH THE CHAIN.

Chassis

RX SX 125

CHAS - 182

«
...
180
181
182
183
184
...
»

Summary of Contents for RX 125




























































































































































































































Reviews:

No comments

Related manuals for RX 125

Brand: Yamaha Pages: 82

Brand: BMW Motorrad Pages: 143

Zero S Series 2014

Brand: Zero Motorcycles Pages: 128

Brand: Honda Pages: 158

Brand: RPS Pages: 28

SPORTTOURING ST4S

Brand: Ducati Pages: 313

Brand: X-lite Pages: 96

Brand: KTM Power Parts Pages: 22

Brand: KTM Power Parts Pages: 12

Brand: KTM Pages: 7

Brand: KTM Pages: 16

125 EXC EU 2014

Brand: KTM Pages: 27

2010 250 EXC-F AUS

Brand: KTM Pages: 125

2009 250 EXC-F SIX DAYS

Brand: KTM Pages: 125

Brand: KTM Pages: 89

Brand: KTM Pages: 208

85 SX 17/14 2021

Brand: KTM Pages: 133

690 Enduro R EU

Brand: KTM Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands