APRILIA RX 125 Service Station Manual Download Page 190

Page: 190 / 219

CYLINDER GASKET

The cylinder gasket (4) must be replaced at every

refitting operation.

SOLENOID

•

Check the control unit as per the dia-

gram.

Installing

•

Remove the fuel tank.

•

Remove the battery with the battery

housing.

•

If the vehicle is a crossover version, re-

move the fixed guillotine by undoing

the two screws (1) and collect the

washers before fitting the RAVE valve.

TOTAL

•

Insert the exhaust valve unit with the

gasket (5) in the cylinder.

CAUTION

REPLACE THE GASKET (5) AT EVERY REFITTING OPER-
ATION.

•

Fit the exhaust valve unit by means of the two screws (1) with the fixed guillotine washers.

•

Fit the control unit with the two screws

(2) on the battery housing frame.

Chassis

RX SX 125

CHAS - 190

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands