APRILIA RX 125 Service Station Manual Download Page 148

Page: 148 / 219

•

Slide off the stem downwards, being careful not to damage its surface.

Draining oil

CAUTION

THE FOLLOWING OPERATIONS REFER TO A SINGLE WHEEL HOLDER STEM / SLEEVE BUT
APPLY TO BOTH

•

Remove the wheel holder stem / sleeve unit.

•

Clean the wheel holder stem / sleeve unit thoroughly.

CAUTION

BEFORE CARRYING OUT THE OPERATIONS BELOW, GET A +440 cm³ (26.85 cu.in) CONTAINER
TO COLLECT THE OIL.

•

Place the sleeve in a vice fitted with

protection shoes.

CAUTION

THE WHEEL HOLDER STEM SLEEVE UNIT CONTAINS
OIL. DO NOT TURN IT OVER OR TILT IT TOO MUCH WHEN
REMOVING IT.

•

Unscrew and remove the upper cap of

the shock absorber rod.

•

With an open wrench keep the lock nut

firm on the shock absorber rod and un-

lock the upper cap.

Suspensions

RX SX 125

SUSP - 148

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands