APRILIA RX 125 Service Station Manual Download Page 181

Page: 181 / 219

•

Check the chain tensioner roller for

wear.

•

Finally, check the swingarm protection

pad for wear.

Installing

•

Check the correct positioning of the

chain on the pinion and the crown.

•

Fit the chain with the two ends joined

at a point between the pinion and the

crown on the lower branch of the chain.

•

Join the two ends of the chain and fit

the master link pins from the inside to

the outside.

•

Insert the plate on the pins.

•

Fit the clip on the pins.

CAUTION

THE MASTER LINK CLIP MUST BE FITTED WITH ITS OPEN
SIDE FACING DIRECTION OPPOSITE THE CHAIN FOR-
WARD MOVEMENT.

Adjusting

To check backslash:

•

Stop the engine.

•

Place the vehicle on its stand.

•

Set the gear level to neutral.

•

Check that the vertical oscillation, between the pinion and the crown in the lower chain

branch, is about 25 - 35 mm (0.99 - 1.38 in)

RX SX 125

Chassis

CHAS - 181

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands