APRILIA RX 125 Service Station Manual Download Page 29

Page: 29 / 219

Cooling system

Level check

Check and top-up

CAUTION

WAIT FOR THE ENGINE TO COOL DOWN BEFORE CHECKING OR TOPPING-UP THE COOLANT
LEVEL.

•

Shut off the engine and wait until it

cools off.

•

Park the vehicle on firm and level

ground.

•

Keep the vehicle upright with the two

wheels on the ground.

•

Turn the radiator cap (1) anticlockwise

just one click.

•

Wait a few seconds so that possible

pressure in the circuit may be purged.

•

Turn the radiator cap (1) anticlockwise

again and remove it.

•

Make sure the fluid covers the radiator

plates completely.

CAUTION

DO NOT ADD ADDITIVES OR OTHER SUBSTANCES TO
THE FLUID.
WHEN USING A FUNNEL OR ANY OTHER ELEMENT,
MAKE SURE IT IS PERFECTLY CLEAN.

CAUTION

COOLANT IS TOXIC IF INGESTED; CONTACT WITH EYES
OR SKIN MAY CAUSE IRRITATION. DO NOT INTRODUCE
YOUR FINGERS OR ANY OTHER OBJECT TO CHECK IF
THERE IS COOLANT OR NOT.

Braking system

RX SX 125

Maintenance

MAIN - 29

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands