APRILIA RX 125 Service Station Manual Download Page 142

Page: 142 / 219

•

Place a stand under the tyre to keep

the wheel in position once it is free.

•

Slide off the wheel pin from the left

side.

•

Collect the spacer from the left side.

•

Remove the wheel by sliding it off from the front.

Checking the front wheel

CAUTION

CHECK THAT ALL THE PARTS ARE IN GOOD CONDITIONS, ESPECIALLY THOSE MENTIONED
BELOW.

BEARINGS

Turn the internal ring manually; it must rotate

smoothly, continuously and silently.

There must be no axial clearance.

The bearings presenting these problems must be

replaced.

GASKETS

Check that the gaskets are in good conditions; replace them if they show signs of damage or excessive

wear.

Suspensions

RX SX 125

SUSP - 142

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands