APRILIA RX 125 Service Station Manual Download Page 59

Page: 59 / 219

Voltage regulator check

•

Output voltage 13.5 V - 15 V

•

Output current higher than 10 A (with

load)

Turn signals system check

Turn indicator device check

Check placing the tester probes on the poles:

+ / - 5.8 kOhm.

- / L (bulb) 5.3 kOhm.

- / L (bulb) 4.8 kOhm.

•

Undo and remove the screw and re-

move the protection glass with caution

so as not to break the fitting tooth.

•

Slightly press the bulb and turn it anti-

clockwise.Take out the bulb from its

fitting.

•

Upon replacement, insert a bulb of

equal rating in the bulb holder, making

the two guiding pins coincide with their

guides on the bulb holder.

RX SX 125

Electrical system

ELE SYS - 59

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands