APRILIA RX 125 Service Station Manual Download Page 141

Page: 141 / 219

19.Seeger ring

20.Front hub pin

Removing the front wheel

CAUTION

UPON REMOVING, PAY ATTENTION NOT TO DAMAGE THE BRAKE HOSES, DISCS AND PADS.

•

Place the vehicle on its OPTIONAL rear service stand.

CAUTION

MAKE SURE THE VEHICLE IS STABLE.
HELPED BY ANOTHER OPERATOR, KEEP THE HANDLEBAR STEADY AND ENGAGED SO THAT
THE STEERING IS LOCKED.

•

Undo and remove both front calliper

fixing screws.

•

Remove the brake calliper.

CAUTION

DO NOT ACTUATE THE FRONT BRAKE LEVER AFTER
REMOVING THE WHEEL. OTHERWISE, THE CALLIPER
PLUNGERS COULD GO OUT OF THEIR SEAT, RESULTING
IN BRAKE FLUID LEAKAGE.

•

Working from the right side, loosen

both screws.

•

Working from the right side, unscrew

and remove the cover.

RX SX 125

Suspensions

SUSP - 141

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands