APRILIA RX 125 Service Station Manual Download Page 150

Page: 150 / 219

•

Drain again all the oil inside the stem.

Disassembling the fork

CAUTION

THE FOLLOWING OPERATIONS REFER TO A SINGLE WHEEL HOLDER STEM / SLEEVE BUT
APPLY TO BOTH

•

Screw the stem, on the foot side, with

a vice fitted with protection jaws to

avoid damaging it.

•

Loosen the fixing screw and remove

the guide of the stem cover.

•

Hold the sleeve and firmly slide it off the

stem.

•

Screw the sleeve in a vice fitted with

protection jaws so as to avoid dam-

ages.

•

With a plain slot screwdriver remove

the dust guard, being careful not to

damage the sleeve rim.

•

The dust guards removed can not be

reused.

Suspensions

RX SX 125

SUSP - 150

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands