APRILIA RX 125 Service Station Manual Download Page 176

Page: 176 / 219

•

Working from the left side, undo and

remove the swingarm pin (7) and col-

lect the two washers.

•

With the help of a second operator, re-

move the swingarm from the chassis.

SWINGARM REMOVAL

•

Remove the swingarm

•

Place the swingarm on a supporting

surface.

•

Clean the two sides of the bearing

seats with a cloth.

•

Remove the external plastic washers

(8).

•

Slide off both needle bearing (11)

bushings from inside the swingarm.

•

Take out the two O-rings (9).

•

Using a buffer of suitable diameter take

out the two roller casings (10).

Checking

CAUTION

CHECK THAT NO COMPONENT IS NOTICEABLY DISTORTED, DAMAGED, CRACKED AND/OR
DENTED.
REPLACE ALL DAMAGED COMPONENTS.

ROLLER CASINGS

Turn the roller casings manually; they must rotate smoothly, continuously and silently.

There must be no axial clearance.

Replace the roller casings that present these problems.

Apply grease on the rollers.

GASKETS

Check that the gaskets are in good conditions; replace them if they show signs of damage or excessive

wear.

Chassis

RX SX 125

CHAS - 176

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands