APRILIA RX 125 Service Station Manual Download Page 98

Page: 98 / 219

•

Fit the protection sleeve on the crank-

shaft thread.

•

Insert the long threaded end of the ex-

tractor screw in the extractor plate and

remove the flywheel.

Removing the stator

•

Undo and remove the three M6 stator

fixing screws.

•

Remove the stator, the cable guide and

external locking.

•

Remove the woodruff key from the

crankshaft.

Installing the flywheel

•

Degrease the crankshaft conic part

and the flywheel.

•

Place the flywheel matching the

grooves on the shaft.

•

Place the washer and the magneto fly-

wheel fixing screw without tightening it.

•

Place the flywheel up to the TDC

Engine

RX SX 125

ENG - 98

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands