APRILIA RX 125 Service Station Manual Download Page 143

Page: 143 / 219

WHEEL PIN

Using a dial gauge, check the wheel pin eccen-

tricity. If the eccentricity exceeds the limit value,

replace the pin.

Maximum eccentricity: 0.25 mm (0.0098 in)

RIM

Using a dial gauge, check that the radial (A) and

the axial (B) eccentricities of the rim do not exceed

the limit value. An excessive eccentricity is usually

caused by worn or damaged bearings. Replace

the rim if, after replacing the bearings, the value is

not within the specified limit.

Maximum radial and axial eccentricity: 2 mm.

TYRE

Check the tyre conditions.

Installing the front wheel

•

Spread a thin layer of lubricating

grease all along the wheel pin.

CAUTION

UPON REFITTING, PAY ATTENTION NOT TO DAMAGE
THE BRAKE HOSES, DISCS AND PADS.

CAUTION

POSITION THE SPACER WITH THE LARGER DIAMETER
SIDE FACING THE FORK RIGHT STEM.

•

Fit the spacer in its position on the wheel.

•

Fit the wheel between the fork stems, on the support.

RISK OF INJURY. BE CAREFUL NOT TO INTRODUCE YOUR FINGERS TO ALIGN THE HOLES.

RX SX 125

Suspensions

SUSP - 143

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands