APRILIA RX 125 Service Station Manual Download Page 217

Page: 217 / 219

- Response to throttle control

- Stability when accelerating and braking

- Front and rear brake efficiency

- Front and rear suspension efficiency

- Abnormal noise

Static test

Static check after test drive:

- Restarting when warmed up

- Starter operation (if present)

- Minimum holding (turning the handlebar)

- Uniform turning of the steering

- Possible leaks

- Radiator electric fan operation (if present)

Functional inspection

- Hydraulic braking system

- Stroke of brake and clutch levers (if present)

- Clutch - Check for correct operation

- Engine - Check for correct general operation and absence of abnormal noise

- Other

- Documentation check:

- Chassis and engine numbers check

- Supplied tools check

- License plate fitting

- Locks checking

- Tyre pressure check

- Installation of mirrors and any possible accessories

NEVER EXCEED THE RECOMMENDED INFLATION PRESSURES AS TYRES MAY BURST.

CAUTION

CHECK AND ADJUST TYRE PRESSURE WITH TYRES AT AMBIENT TEMPERATURE.

RX SX 125

Pre-delivery

PRE DE - 217

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands