APRILIA RX 125 Service Station Manual Download Page 107

Page: 107 / 219

Disassembling the piston

•

Remove the cylinder.

•

Remove one of the two seeger rings of

the pin using a suitable tool.

CAUTION

BEFORE TAKING OUT THE PIN SEEGER RING, COVER
THE CRANKCASE OPENING WITH A CLOTH SO THAT THE
RING DOES NOT FALL INTO THE CRANKCASE.

NOTE

IT IS NOT NECESSARY TO REMOVE BOTH PIN SEEGER
RINGS.

•

Tap the pin out with a suitable punch.

CAUTION

WHILE TAPPING OUT THE PIN, HOLD THE PISTON WITH
ONE HAND SO THAT THE CONNECTING ROAD DOES NOT
BEND.

•

Remove the piston and collect the ball

retainer.

CAUTION

WHILE TAPPING OUT THE PIN, HOLD THE PISTON WITH
ONE HAND SO THAT THE CONNECTING ROAD DOES NOT
BEND.

See also

Removing the cylinder

RX SX 125

Engine

ENG - 107

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands