APRILIA RX 125 Service Station Manual Download Page 194

Page: 194 / 219

12.D11x6.6x1 green clic clamp

13.D28x8.6 clic clamp

14.D23.5x8 clic clamp

15.D23.5x8 clic clamp

16.D10.1 clamp

17.5x9 pipe

18.TE flanged screw M6x25

Coolant replacement

CAUTION

DO NOT USE YOUR VEHICLE IF THE COOLANT IS BELOW THE MINIMUM LEVEL.
CHECK THE COOLANT LEVEL PERIODICALLY OR AFTER LONG TRIPS.

•

Remove both front side fairings.

•

Place a container of suitable capacity

underneath the sleeve.

•

Release the clamp.

•

Slide off the sleeve.

•

Empty the liquid into the container.

•

Open the radiator cap to facilitate

drainage.

•

Unscrew and remove the drainage

plug (1) indicated by the mark OUT.

•

Unscrew and remove the radiator plug

to facilitate draining the coolant.

CAUTION

DO NOT DISPOSE OF THE FLUID INTO THE ENVIRON-
MENT.

•

Wait for the coolant to drain off and tighten the screw.

Cooling system

RX SX 125

COOL SYS - 194

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands