APRILIA RX 125 Service Station Manual Download Page 169

Page: 169 / 219

Installing

SHOCK ABSORBER FITTING

•

Fit the shock absorber by inserting

from the bottom.

•

Insert the shock absorber upper screw

with the washer from the left side.

•

Working from the opposite side, tighten

the nut (1).

•

Position the connecting rod assembly

on the shock absorber.

•

Insert the shock absorber lower screw

from the right side.

•

Working from the opposite side, tighten

the nut (2).

•

Place the double connecting rod in its

seat on the chassis.

•

From the left side insert the nut fixing

the connecting rod assembly plus the

washer in the chassis.

•

Working from the opposite side, tighten

the nut (3).

•

Remove the support between the

swingarm and the saddle post frame.

Linkages

RX SX 125

Suspensions

SUSP - 169

Summary of Contents for RX 125




























































































































































































































Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands

APRILIA RX 125, Service Station Manual

Search results

Summary of Contents for RX 125

Reviews:

Related manuals for RX 125

Brands by name

Popular brands