APRILIA CAPONORD 1200 Service Station Manual Download Page 53

Page: 53 / 439

Crankshaft class (crank pin)

There are four different classes of crankshaft avail-

able (0, 1, 2, 3), selected in relation to crank pin

diameter.

There are four different classes of crankshaft avail-

able (E1, E2, ...) selectable in relation to connect-

ing rod weight.

Key:

* Class according to connecting rod weight.

** Class according to crank pin diameter.

*** Serial number for traceability and indicating date.

SHAFT CATEGORY

Class

Crank pin diameter (mm)

42.000 - 42.006 mm (1.65354 - 1.65377 in)

41.994 - 42.000 mm (1.65330 - 1.65354 in)

41.988 - 41.994 mm (1.65307 - 1.65330 in)

41.982 - 41.988 mm (1.65283 - 1.65307 in)

See also

Removing the flywheel cover

Selecting bushings

There is only one dimension class for the connecting rod. As a result, the bushings used must be

selected in accordance with the dimension class of the crank pin.

BUSHINGS

Crank pin diameter

Connecting rod class 1

Crankshaft class 0

Semi-bushing type E (green)

Crankshaft class 1

Semi-bushing type A (red)

Crankshaft class 2

Semi-bushing type B (blue)

Crankshaft class 3

Semi-bushing type C (yellow)

Selecting connecting rods

Not all weight classes are available as spare parts. Only the two most significant weight classes are

available - refer to the following table for selection:

CONNECTING RODS

Class according to

crankshaft weight

Original connecting rod class (colour)

Original connecting

rod class ("E"

marking)

Spare part connecting

rod class

Brown connecting rod

Cat. A

Blue connecting rod

Cat. A

Yellow connecting rod

Cat. A

Green connecting rod

Cat. A

Pink connecting rod

Cat. B

Black connecting rod

Cat. B

White connecting rod

Cat. B

CAUTION

CAPONORD 1200

Characteristics

CHAR - 53

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands