APRILIA CAPONORD 1200 Service Station Manual Download Page 151

Page: 151 / 439

throttle body connector and control unit connector and check if there is cables continuity; if

there is no continuity, restore the cable harness. If there is continuity, with the throttle body

connector connected, check that the resistance, from the throttle control unit connector,

between PIN 3 and 15 is within 1 and 2.5 Ohm; if it is not, replace the throttle body; if it is,

check that the throttle body is not mechanically blocked: if blocked, solve the problem and

replace the body; if it is not, replace the control unit

DIAGNOSIS INSTRUMENT: LOGIC ERRORS

potentiometer 1 sensor, front throttle position P0121

•

signal not valid

Error cause

•

Signal not within the expected value drawn according to the values of the intake pressure

Troubleshooting

•

Check the parameter of the Potentiometer 1 Front throttle (voltage) to get which signal the

control unit receives and to compare it to the Potentiometer 1 Rear throttle (voltage). Check

the throttle body connector as well as the control unit connector. Check that cable resistance

between the throttle body connector (PIN 1) and the control unit (PIN48) is a few tenths of

an Ohm. If this is not the case, restore the cable harness. If the value is correct, replace the

complete throttle body

potentiometer 2 sensor, front throttle position P0123

•

signal not valid

Error cause

•

Signal not within the expected value drawn according to the values of the intake pressure

Troubleshooting

•

Check the parameter of the Potentiometer 2 Front throttle (voltage) to get which signal the

control unit receives and to compare it to the Potentiometer 2 Rear throttle (voltage). Check

the throttle body connector as well as the control unit connector. Check that cable resistance

between the throttle body connector (PIN 4) and the control unit (PIN 50) is a few tenths of

an Ohm. If this is not the case, restore the cable harness. If the value is correct, replace the

complete throttle body

front throttle position potentiometer P0124

•

incongruent signal

Error cause

CAPONORD 1200

Electrical system

ELE SYS - 151

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands