APRILIA CAPONORD 1200 Service Station Manual Download Page 175

Page: 175 / 439

Pin out:

1. Supply from VCU

2. Output 1

3. -

4. Supply from VCU

5. Output 2

6. -

7. Ground from VCU

8. Ground from VCU

DIAGNOSTICS INSTRUMENT: ADJUSTMENTS

Rotary sensor reset

•

When the motorbike comes off the assembly line, a setup measurement (in mm) is set

(height from the ground) that the system recognises as reference position.

•

In case of replacement of the rotary potentiometer or of the VCU control unit, it is necessary

to reset the potentiometer by putting the motorbike on the central stand with the rear wheel

raised above the ground.

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

VCU ERRORS

Error rotary sensor Output 1 shortcircuit or open circuit C1404

Error cause

•

If shortcircuit: an excessive or a null tension has been detected on PIN B3 VCU. If the circuit

is open: an interruption has been detected.

Troubleshooting

•

If shortcircuit: disconnect the connector of the rotary sensor and check its insulation from

ground and supply system of PIN 2: if the insulation is not present, restore the cabling,

otherwise replace the sensor.

•

If the circuit is open: Check the connector on the component and the VCU connector. Dis-

connect the two connectors and check the continuity of the cable between PIN 2 sensor and

PIN B3 VCU and restore the cable harness. If the cable harness is not damaged, replace

the sensor.

Error rotary sensor Output 2 shortcircuit or open circuit C1405

Error cause

•

If shortcircuit: an excessive or a null tension has been detected on PIN C3 VCU. If the circuit

is open: an interruption has been detected.

Troubleshooting

CAPONORD 1200

Electrical system

ELE SYS - 175

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands