APRILIA CAPONORD 1200 Service Station Manual Download Page 124

Page: 124 / 439

the key to OFF and check continuity between the ENGINE connector PIN 25 and the sensor

connector PIN 1: if not OK, restore the cable harness; if OK, replace the control unit; if there

is 5V voltage at PIN 1, and with key set to ON, check the continuity to ground of the sensor

connector PIN 3: if not OK, restore the cable harness; if OK, replace the sensor.

rear cylinder air pressure sensor P0106

•

shorted to positive / open circuit, shorted to negative.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 49. If the circuit is open,

shorted to negative: voltage equal to zero has been detected at PIN 49.

Troubleshooting

•

If shorted to positive: verify that the parameter of the rear cylinder air Pressure Sensor on

the diagnosis instrument is approx. 1200 mbar; disconnect the sensor connector: if the value

does not vary, it means that the cable is shorted between the control unit connector and the

sensor connector: restore the cable harness; Replace the sensor if the value varies.

•

If the circuit is open, shorted to negative: check the Marelli control unit connector and the

sensor connector; if not OK, restore. If everything is OK, with key set to OFF, check if there

is continuity between the PIN 49 of the Marelli control unit and the sensor connector PIN 3:

if there is no continuity, restore the cable harness. If there is continuity, check the cable

ground insulation: if there is continuity to ground, restore the cable harness; if not, with key

set to ON check that the voltage on sensor connector PIN 1 is approx. 5 V: if not OK, set

the key to OFF and check continuity between the ENGINE connector PIN 25 and the sensor

connector PIN 1: if not OK, restore the cable harness; if OK, replace the control unit; if there

is 5V voltage at PIN 1, and with key set to ON, check the continuity to ground of the sensor

connector PIN 3: if not OK, restore the cable harness; if OK, replace the sensor.

DIAGNOSIS INSTRUMENT: LOGIC ERRORS

front cylinder air pressure sensor P0107

•

signal not valid.

Error cause

•

According to the engine operation data (rpm, throttle, etc.) an average value for the intake

pressure is estimated: if the value read deviates by a given percentage, this error is activa-

ted. The most frequent causes can be: abnormal resistance in the sensor circuit (for

example, rusted terminals) or sensor with poor performance.

Troubleshooting

•

Check the Marelli control unit connector and the sensor connector; if not OK, restore. If

everything is OK, check that resistance between ENGINE connector PIN 24 and sensor

Electrical system

CAPONORD 1200

ELE SYS - 124

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands