APRILIA CAPONORD 1200 Service Station Manual Download Page 252

Page: 252 / 439

•

Remove the counterweight and de-

compression device with the relevant

spring.

•

To refit, engage spring on decompres-

sion device and preload it by one turn.

•

Install the counterweight and engage

the preloaded device to it.

•

Tighten the counterweight fixing

screw.

Installing camshafts

The camshaft refitting procedure is described in the "Timing" section.

See also

Timing

Rear head removal

•

Remove the magneto flywheel.

•

Unscrew and remove the screw and

collect the washer and the internal

spring.

Engine

CAPONORD 1200

ENG - 252

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands