APRILIA CAPONORD 1200 Service Station Manual Download Page 256 | Manualshive

Page: 256 / 439

background image

•

Remove the fixed chain slider.

NOTE

ON REASSEMBLY, PERFECTLY CLEAN THE MATING
SURFACE OF THE SPECIAL SCREW RETAINING THE
IDLE GEAR AND THE THREE TIMING GEARS AND RE-
PLACE THE ALUMINIUM WASHER.

Rear head check

•

Using a round scraper, clean off any carbon deposits in the combustion chamber.

CAUTION

DO NOT USE A POINTED INSTRUMENT TO AVOID DAMAGING OR SCRATCHING THE SPARK
PLUG THREADS OR THE VALVE SEATS.

•

Check that cylinder head is not damaged or scratched; replace it if necessary.

•

Check that there are no mineral deposits or rust in the cylinder head water cooled jacket;

remove them if necessary.

•

Check that the tappet covers and the camshaft toothed wheel cover are not damaged or

worn; replace the defective part(s).

Valves

Valve removal

•

Remove the head.

•

Place the head on supporting surface.

•

Number the valves and their bucket tappets in order to position them correctly upon refitting.

•

Remove the bucket tappets and the

adjustment shims using a magnet.

Engine

CAPONORD 1200

ENG - 256

«
...
254
255
256
257
258
...
»

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CAPONORD 1200

Brand: HRC Pages: 88

Brand: SCORPION Pages: 12

Brand: Happy Trails Pages: 4

Brand: GAS GAS Pages: 32

Brand: Honda Pages: 26

Brand: hepco & becker Pages: 7

Brand: SHERCO Pages: 102

Brand: DYNATEK Pages: 12

Brand: BMW Pages: 205

Brand: SpeedAngle Pages: 37

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 41

Brand: Yamaha Pages: 8

Brand: Yamaha Pages: 101

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 119

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands