APRILIA CAPONORD 1200 Service Station Manual Download Page 141

Page: 141 / 439

Marelli control unit: if not OK, restore; if OK, check continuity of cable harness (Brown/Black

cable)

Coil

Coils key:

1. Front cylinder central coil

2. Front cylinder side coil

3. Rear cylinder central coil

4. Rear cylinder side coil

Function

Spark generation

Operation / Operating principle

Inductive discharge system

Level in electrical circuit diagram:

Coils and injectors

Location:

•

on the vehicle: on the head covers.

•

connector:

- FRONT CENTRAL COIL with long cable, left side, on the frame near filter box cover, above the front

side coil connector.

- FRONT SIDE COIL with short cable and retaining tongue, left side, on the frame near filter box cover,

below the front central coil connector.

- REAR CENTRAL COIL with long cable, at the centre, under the filter box, at the back compared to

connector.

- REAR SIDE COIL with short cable and retaining tongue, at the centre, under the filter box, at the front

compared to the rear central coil connector.

Electrical specifications:

CAPONORD 1200

Electrical system

ELE SYS - 141

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands