APRILIA CAPONORD 1200 Service Station Manual Download Page 208

Page: 208 / 439

•

Working on the right side, insert the

three bolts with their washers.

•

Working on the right side, place the

spacers on the three bolts between the

engine block and the chassis.

CAUTION

THE SPACERS HAVE DIFFERENT SIZES. REFIT THEM IN
THE SAME WAY THEY WERE BEFORE BEING REMOVED.

•

Working from the left side, tighten the

three nuts.

•

Release the engine from the belt and

the hoist.

•

Refit the pinion and restore the gearing

chain clearance.

•

Reconnect the electric connections

and clamp the cable harnesses.

•

Carry out the vehicle preparation oper-

ations but in reverse order, restore the

correct level of all fluids and carry out

the adjustments that may be required.

Engine from vehicle

CAPONORD 1200

ENG VE - 208

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands