APRILIA CAPONORD 1200 Service Station Manual Download Page 106

Page: 106 / 439

•

short circuit to positive/ short circuit to negative / open circuit

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 31. If shorted to negative:

no voltage has been detected. If the circuit is open: an interruption has been detected

Troubleshooting

•

If shorted to positive: check the relay electrical specifications are correct by disconnecting

it from the cable harness. If they are not correct, replace the relay; if OK, restore the cable

harness (Blue/Pink cable)

•

If shorted to negative: check the relay electrical specifications are correct by disconnecting

it from the cable harness. If they are not correct, replace the relay; if OK, restore the cable

harness (Blue/Pink cable)

•

If the circuit is open: check the relay electrical characteristics are correct by disconnecting

it from the cable harness; if not OK, replace the relay, if OK, check relay connector, engine-

vehicle cable harness connector and ENGINE connector of the Marelli control unit: if not

OK, restore; if OK, check continuity of cable harness (Blue/Pink cable)

DIAGNOSTICS INSTRUMENT: LOGIC ERRORS

Level 2 safety reset P0608

Error cause

•

As the level 2 safety system (comparison between requested torque and calculated torque)

has detected a fault, the control unit has reset engine (C gravity). The instrument panel does

not indicate the presence of this error even in the ATT status.

Troubleshooting

•

Continue fault search for the other errors detected.

Safety Engine Stop P0609

Error cause

•

Since the safety system has detected a serious fault, the control unit has shut off the engine.

Troubleshooting

•

Continue fault search for the other errors detected.

Saved data file (for safety) P0611

•

Filled

Error cause

•

This indication appears only if the Level 2 safety has reset the engine (C gravity). The in-

strument panel does not indicate the presence of this error even in the ATT status.

Troubleshooting

•

Continue fault search for the other errors detected.

DIAGNOSTICS INSTRUMENT: ADJUSTMENTS

Electrical system

CAPONORD 1200

ELE SYS - 106

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands