APRILIA CAPONORD 1200 Service Station Manual Download Page 370

Page: 370 / 439

Removal

•

Remove the cotter pin.

•

Remove the pin by sliding it back-

wards.

•

Extract one pad at a time.

CAUTION

AFTER REMOVING THE PADS, DO NOT OPERATE THE
BRAKE LEVER OR THE CALLIPER PLUNGERS COULD
GO OUT OF THEIR SEATS RESULTING IN BRAKE FLUID
LEAKS.

Bleeding the braking system

VEHICLE PREPARATION

•

It is important to check that there is always enough brake fluid in the reservoir.

•

Using a bleed device facilitates these operations while, in the meantime, the "Brake fluid

replacement" operations are performed.

•

In this case, the bleed process must be accompanied by further pedal strokes and with the

bleed device connected (about 5 for each wheel circuit).

Braking system

CAPONORD 1200

BRAK SYS - 370

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands