APRILIA CAPONORD 1200 Service Station Manual Download Page 293

Page: 293 / 439

•

Bend the chamfering tongue.

•

Refit the clutch.

See also

Assembling the

clutch

Blow-by

The Blow By system allows for oil vapours to be recycled. The law requires that these gas and oil

vapours cannot be released into the atmosphere for environmental reasons. Therefore, there are sys-

tems for the recirculation of these gas-oil vapours inside the intake ducts to burn them in the subsequent

active phases of the engine. This system separates the engine oil into oil vapour.

The oil vapours coming from the joints (1) and (2), are filtered and enter into the filter box through the

joint (4).

CAPONORD 1200

Engine

ENG - 293

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands