APRILIA CAPONORD 1200 Service Station Manual Download Page 165 | Manualshive

Page: 165 / 439

background image

DIAGNOSTICS INSTRUMENT: ADJUSTMENTS

Exhaust valve - Zero position search

•

After having pressed the enter button for the zero position search, shut off the vehicle and

leave the keys in OFF, even in the event that the instruments indicate the opposite.

•

Slacken the exhaust throttle valve cable tension.

NOTE

IF IT IS NECESSARY TO REPLACE THE MOTOR, FROM POSITION ZERO LOOSEN THE CABLES
COMPLETELY TO REMOVE THEM, THEN, AFTER DISCONNECTING THE CONNECTOR, RE-
MOVE THE MOTOR ITSELF.

•

Using the specific adjuster screw, tension the upper cable and leave around 1.8 mm (0.07

in) between the retainer and opening travel limit of the valve.

•

Using the specific adjuster screw, tension the lower cable until the tensioning is as close as

possible to the one of the upper cable (failing this the subsequent adjustment with the tool

will fail).

•

Tightening the lower cable will probably have caused the travel limit to shift: repeat the

procedure until the correct position is obtained.

•

Turn the key to ON.

CAUTION

THE ZERO SEARCH OF THE DISCHARGE VALVE MOTOR PROCEDURE ENTAILS RESETTING
THE EXISTING MECHANICAL STOPS. AN ERROR FOR STOP SEARCH NOT CARRIED OUT IS
THEN INDICATED, WHICH REMAINS UNTIL THE SELF-LEARNING OF THE DISCHARGE VALVE
PROCEDURE IS PERFORMED. DO NOT CARRY OUT THIS OPERATION WHEN USING A NON-
ORIGINAL EXHAUST SYSTEM WHERE ANY CABLES CONSIDERED NOT NECESSARY HAVE
BEEN DISCONNECTED.

Exhaust valve - Self-acquisition

•

The search for the opening travel limit (open valve) and of the closing travel limit (closed

valve) is performed. During both normal operation and the self-cleaning cycle, the valve will

only move within this range and without reaching the mechanical end stops, to prevent strain

to the electric motor.

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

CAPONORD 1200

Exhaust butterfly valve stop research P0191

CAPONORD 1200

Electrical system

ELE SYS - 165

«
...
163
164
165
166
167
...
»

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CAPONORD 1200

Brand: Suzuki Pages: 206

Brand: DUCATI Performance Pages: 5

Brand: KTM Power Parts Pages: 7

V-Gard 500 Series

Brand: MSA Pages: 2

Brand: Apollo Pages: 92

Brand: Kabuto Pages: 20

RMAX WOLVERINE 2021

Brand: Yamaha Pages: 192

Brand: Yamaha Pages: 396

Brand: Yamaha Pages: 192

Brand: Yamaha Pages: 164

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 80

Brand: Bajaj Pages: 44

Brand: Takegawa Pages: 2

Brand: Hama Pages: 22

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 22

Brand: Yamaha Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands