APRILIA CAPONORD 1200 Service Station Manual Download Page 158

Page: 158 / 439

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

Gear sensor P0461

•

shorted to positive or open circuit / shorted to negative.

Error cause

•

If the circuit is open, shorted to positive: excessive voltage has been detected at PIN 72. If

shorted to negative: voltage equal to zero has been detected at PIN 72.

Troubleshooting

•

If the circuit is open, shorted to positive: the error is detected with gear engaged only. Check

the sensor connector and the VEHICLE connector of the control unit: if not OK, restore; if

they are OK, check the continuity of the Grey/Black cable between the two connectors: if

not OK, restore; if they are OK, with key set to ON and control unit connector disconnected,

check from the control unit side if the cable is in voltage: if it is in voltage, disconnect the

sensor connector and check if the cable is in voltage: if it is in voltage, restore the cable

harness; if it is not in voltage, replace the sensor (there is an interruption or shorted to positive

of the Pink/Black cable in the section from the sensor connector to the sensor or inside the

sensor).

•

If shorted to negative: disconnect the sensor connector and with key set to ON, check Grey/

Black cable voltage: if equal to zero, restore the cable harness; if equal to approx. 5 V,

replace the sensor (there is short circuit to ground of the Pink/Black cable in the section from

the sensor connector to the sensor or inside the sensor).

Side stand sensor

Function

It tells the side stand position to the control unit.

Operation / Operating principle

If the gear is engaged and the side stand is unfol-

ded, and therefore the circuit is open, the control

unit does not enable vehicle start-up or shuts off

the engine if it is rotating.

Level in electrical circuit diagram:

Start-up enabling switches

Location:

•

on the vehicle: on the stand

•

connector: on the alternator cover (2-

way connector)

Pin out:

Electrical system

CAPONORD 1200

ELE SYS - 158

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands