APRILIA CAPONORD 1200 Service Station Manual Download Page 226

Page: 226 / 439

Installing the flywheel

•

Insert the woodruff key on the crank-

shaft.

•

Insert the start-up transmission gear

after applying a layer of grease.

•

Insert the flywheel on the crankshaft.

•

Screw the screw together with the

washer but without tightening.

•

Place the appropriate tool for locking

the flywheel.

•

Locking the flywheel in position, using

the specific tool, tighten the screw on

the crankshaft.

WARNING!:

TO APPLY THE CORRECT TIGHTENING TOR-

QUE, CHECK THE MEASUREMENT OF THE

SCREW THAT MAY BE M12 OR M14.

•

Remove the special tool.

Engine

CAPONORD 1200

ENG - 226

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands