APRILIA CAPONORD 1200 Service Station Manual Download Page 91

Page: 91 / 439

Check the cable harness of the CAN line.

ENGINE TEMPERATURE

Error code B0010 (ENGINE OVERTEMPERATURE)

Error cause

Engine temperature > 115 °C.

Troubleshooting

The error is no longer displayed when the temperature falls below 113 °C. If the error continues to be

displayed also with low engine temperature, the failure is probably in the sensor that is shortcircuited

or in the cable harness: perform the diagnosis by connecting to the engine control unit.

HEATED HANDGRIPS

Error code B0011 (HANDGRIPS HEATING BUTTON LOCKED)

Error cause

Alarm handgrips button locked:

This alarm occurs when, for various reasons, the activation button is locked.

Identification

Fixed warning light.

Troubleshooting

Check the correct operation of the contact of the button and the insulation from ground and from supply

of PIN 15 of the instrument panel (grey connector).

Battery recharge circuit

RECHARGING SYSTEM

•

Remove the tank and the filter casing;

•

Disconnect the three-way connector

(1) (white).

NOTE

THE ENGINE SIDE IS IDENTIFIED WITH THE LETTER "A"

Measurement of resistance (with engine off)

•

For a correct detection of the alternator

resistance, an ambient temperature

measurement must be carried out and

afterwards a heat stabilisation (after

turning fan on) by using a tester, using

alternatively the 3 connector pins:

CAPONORD 1200

Electrical system

ELE SYS - 91

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands