APRILIA CAPONORD 1200 Service Station Manual Download Page 372

Page: 372 / 439

•

Detach the bleed hoses and close the

bleed screws again to the correct tight-

ening torque.

•

Check the stroke and the sensitivity of

both the lever and the brake pedal.

NOTE: IF AFTER BLEEDING, THE STROKE OF

THE PEDAL OR THE LEVER IS TOO LONG,

CHECK THAT THERE ARE NO LEAKS IN THE

BRAKING SYSTEM AND IF EVERYTHING IS

OK. CONTINUE BLEEDING OPERATIONS US-

ING THE DIAGNOSIS INSTRUMENT.

BRAKE BLEEDING AFTER ABS CONTROL

UNIT REPLACEMENT

VEHICLE PREPARATION

•

Connect the bleed bottle to the bleed

screws of the front and rear callipers

and open it.

•

Fully press down the lever and the

brake pedal and fix them into position

with the respective locking devices.

•

Close the bleed screws of the front and

rear callipers and remove the bleed

bottle.

•

Remove the damaged ABS control

unit.

Note: First of all, detach the brake pipes that

go from the ABS control unit to the brake pump

(1-4) and immediately seal the opened unions

of the ABS control unit with protective caps.

Afterwards, remove pipes (2-3) that go from the

ABS control unit to the brakes and also seal

these unions with protective caps.

•

Install the new ABS control unit, previ-

ously filled up.

•

So that the brake fluid remains in the

ABS control unit, first remove the pro-

Braking system

CAPONORD 1200

BRAK SYS - 372

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands