APRILIA CAPONORD 1200 Service Station Manual Download Page 327

Page: 327 / 439

Assembling

•

Grease the lower and upper bearing

rollers

•

Prefit the shim, dust gaiter and lower

bearing on the steering yoke as shown

in the figure.

Recommended products

AGIP MP GREASE

Grease for bearings, joints,

couplings and linkages

As an alternative to the recommended product,

use top brand grease for roller bearings with an

operating temperature range of -22°F to +284°F

(-30°C to +140°C), drop point between 302ºF to

446°F (150°C to 230°C), high corrosion protection

qualities and good water and rust resistance.

•

Install the upper bearing on the steer-

ing yoke pin as shown in the figure,

with the conical part facing downward.

•

After inserting, the bearing must slide

freely on the steering pin till matching

with the steering bearing conic in the

frame.

•

Ensure the bearing mating in its seat,

using a teflon buffer from a suitable di-

ameter.

CAPONORD 1200

Suspensions

SUSP - 327

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands