APRILIA CAPONORD 1200 Service Station Manual Download Page 176

Page: 176 / 439

•

If shortcircuit: disconnect the connector of the rotary sensor and check its insulation from

ground and supply system of PIN 5: if the insulation is not present, restore the cabling,

otherwise replace the sensor.

•

If the circuit is open: Check the connector on the component and the VCU connector. Dis-

connect the two connectors and check the continuity of the cable between PIN 5 sensor and

PIN C3 VCU and restore the cable harness. If the cable harness is not damaged, replace

the sensor.

Error rotary sensor failed consistency C1406

Error cause

•

The sum of the tensions detected on the two outputs of the sensor (PIN 2 and PIN 5) is

different from 5 V.

Troubleshooting

•

Replace the sensor.

Preload motor

(IF APPLICABLE)

Function

Check the preload of the rear single shock ab-

sorber in order to keep the optimal setup.

Operation / Operating principle

It is possible to adjust the preload of the spring of

the rear shock absorber using an electrical device,

on 5 positions, which are highlighted with specific

icons on the digital instrument panel: only rider,

only rider with luggage, rider with passenger, rider

with passenger and luggage, automatic. During

the automatic operation, the system will adjust au-

tomatically the preload level, on the basis of the

motorbike load, in order to maintain the optimal

setup. The system works in two phases:

1. With the vehicle at a standstill, the engine run-

ning, gear in idle, crutch closed, the system per-

forms a first overall preload adjustment.

2. With the vehicle moving, the system constantly

monitors (cyclically every minute) various signals

coming from the vehicle and if some conditions are

Electrical system

CAPONORD 1200

ELE SYS - 176

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands