APRILIA CAPONORD 1200 Service Station Manual Download Page 190

Page: 190 / 439

•

Replace the Marelli control unit.

CAN line without signals U1602

•

Bus Off.

Error cause

•

No communication on CAN line (PIN 66 and/or PIN 80): problem on the whole network (for

example, battery cut-off or short circuited or shorted to ground).

Troubleshooting

•

Check the Marelli control unit VEHICLE connector: if not OK, restore; if OK, check the ground

insulation of the two CAN lines from PIN 66 and PIN 80 of the VEHICLE connector: if not

OK, restore cable harness; if OK, check the continuity of the two CAN lines from Marelli

control unit VEHICLE connector to the instrument panel connector: if not OK, restore the

cable harness; if OK, check that the two lines are not shorted to positive testing each of the

2 connectors (Marelli control unit and instrument panel connector) with 1 connector discon-

nected at a time and by setting the key to ON: If not OK, restore; if OK, replace the Marelli

control unit.

CAN line towards instrument panel U1701

•

no signal.

Error cause

•

No signal is received from the instrument panel.

Troubleshooting

•

Check the connector of the instrument panel: if not OK, restore; if OK, check the continuity

of the two lines from the instrument panel connector to the VEHICLE connector of the Marelli

control unit: if not OK, restore the cable harness; if OK, replace the instrument panel.

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

CAN line towards instrument panel U1702 - Intermittent signal or communication error

Error cause

•

Probable bad contact in the CAN line.

Troubleshooting

•

Check the pins 66 and 80 and the Vehicle connector of the Marelli control unit. If not OK,

restore. If OK, check pins 26 and 27 and the instrument panel connector. If not OK, restore.

If OK, check overall operation of the Marelli control unit and instrument panel: replace the

affected component if you find any fault

CAN line towards ABS control unit U1712 - Intermittent signal or communication error

Error cause

•

Probable bad contact in the CAN line

Troubleshooting

Electrical system

CAPONORD 1200

ELE SYS - 190

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands