manualshive.com logo in svg

APRILIA CAPONORD 1200, Service Station Manual

The APRILIA CAPONORD 1200, a powerful and versatile adventure bike, gets even better with the comprehensive "Service Station Manual". Packed with vital information, this manual is a must-have for maintenance and repairs. Download it for free from manualshive.com to unlock the full potential of your Aprilia Caponord 1200.

Share
Download
background image

tective caps of the braking circuit un-

ions and connect the respective pipes.

Once all the braking circuits have been con-

nected, remove the protective caps from the

braking pump unions and connect the braking

pump pipes to the ABS control unit.

•

Unlock the lever and the brake pedal.

•

Remove the cap of the reservoir and fill

it with the new DOT 4 brake fluid up to

the reference "MAX".

•

Reinstall the cap.

CAUTION

PERFORM THE REGULAR BRAKING SYSTEM BLEED, AS
DESCRIBED AT THE BEGINNING OF THE CHAPTER.

•

Check the stroke and the sensitivity of both the lever and the brake pedal.

•

If, after bleeding, the pedal or the lever stroke is too long, check that there are no leaks in

the braking system and if everything is OK, continue bleeding operations using the diag-

nostics instrument as described.

•

Detach the bleed hoses and close the bleed screws again to the correct tightening torque.

BRAKE BLEEDING AFTER CALLIPER RE-

PLACEMENT

VEHICLE PREPARATION - The operations are

described for the front system, but they are al-

so valid for both braking systems.

•

Connect the bleed bottles to the bleed

screw of the front calliper and open it.

•

Fully press down the brake lever and

fasten it into position with a locking de-

vice so as to avoid fluid flowing out from

the open system.

•

Close the bleed screws of the front cal-

liper and remove the bleed bottle.

•

Replace the damaged calliper with a

new one.

•

Unlock the brake lever.

CAPONORD 1200

Braking system

BRAK SYS - 373

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CAPONORD 1200

yasuni R2 Assembly Instructions Manual preview
R2
Brand: yasuni Pages: 11
BMW C 400 X Rider'S Manual preview
C 400 X
Brand: BMW Pages: 245
KYMCO PEOPLE S 125 Owner'S Manual preview
PEOPLE S 125
Brand: KYMCO Pages: 55
R&G BRG0015SS Fitting Instructions Manual preview
BRG0015SS
Brand: R&G Pages: 24
Suzuki 2001 GSX1300RK1 HAYABUSA Supplementary Service Manual preview
2001 GSX1300RK1 HAYABUSA
Brand: Suzuki Pages: 31
Denali LAH.07.10401 Instruction Manual preview
LAH.07.10401
Brand: Denali Pages: 2
Yamaha XV250P1 Owner'S Manual preview
XV250P1
Brand: Yamaha Pages: 98
Yamaha Star 2011 Owner'S Manual preview
Star 2011
Brand: Yamaha Pages: 108
Yamaha XVZ13TFY Owner'S Manual preview
XVZ13TFY
Brand: Yamaha Pages: 124
Yamaha ROAD STAR XV16A Owner'S Manual preview
ROAD STAR XV16A
Brand: Yamaha Pages: 117
Yamaha X MAX CZD300P 2022 Owner'S Manual preview
X MAX CZD300P 2022
Brand: Yamaha Pages: 142
Yamaha XVS13AW(C) Owner'S Manual preview
XVS13AW(C)
Brand: Yamaha Pages: 97
Yamaha V-star XVS650P Owner'S Manual preview
V-star XVS650P
Brand: Yamaha Pages: 119
Yamaha XVS650H 2016 Owner'S Manual preview
XVS650H 2016
Brand: Yamaha Pages: 96
hepco & becker 5057552 00 01 Quick Start Manual preview
5057552 00 01
Brand: hepco & becker Pages: 4
hepco & becker 5052515 00 01 Manual preview
5052515 00 01
Brand: hepco & becker Pages: 4
DYNATEK D4K-DCT Manual preview
D4K-DCT
Brand: DYNATEK Pages: 1
Malaguti F18 WARRIOR Manual preview
F18 WARRIOR
Brand: Malaguti Pages: 383

Brands by name

Popular brands

Load more brands