APRILIA CAPONORD 1200 Service Station Manual Download Page 188

Page: 188 / 439

ABS control unit pin out key:

. Power ground connection 1

. Power ground connection 2

. Vehicle speed signal

. Live supply

. CAN H line

. CAN L line

. -

. ABS warning light

. -

. Rear ABS sensor positive

. Rear ABS sensor negative

. Front ABS sensor negative

. Front ABS sensor positive

. Power ground connection 3

. Serial line

. -

. Battery supply

Can line

Function

It allows communication between the Marelli injection ECU and the instrument panel.

Operation / operating principle

CAN SYSTEM ADVANTAGES

A CAN (controller Area network) line is a connection among the vehicle several electronic devices,

organised as a computer network (Internet). The CAN network has greatly simplified the electrical sys-

tem layout and consequently, its complexity. With this communication line, needless duplication of

several sensors present on the motorbike has been obviated. The sensor signals are shared by the two

electronic elaboration units (instrument panel and control unit).

•

Cable number reduction: The CAN line travels through a twisted cable to several nodes.

•

These nodes can also isolate the errors without causing a system breakdown (FaultsCon-

fination).

•

Immunity to interference: the signal travels through two cables and the signal reading is

differential (voltage difference between the two signals on both cables). If the two signals

are disturbed by an external factor, their difference remains unaltered.

Electrical system

CAPONORD 1200

ELE SYS - 188

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands