APRILIA CAPONORD 1200 Service Station Manual Download Page 374

Page: 374 / 439

•

Remove the cap of the reservoir and fill

it with the new DOT 4 brake fluid up to

the reference "MAX".

•

Reinstall the cap.

BRAKING SYSTEM BLEEDING (only the new

calliper)

CAUTION

PERFORM THE REGULAR BRAKING SYSTEM BLEED, AS
DESCRIBED AT THE BEGINNING OF THE CHAPTER.

•

Check the stroke and the sensitivity of both the lever and the brake pedal.

•

If, after bleeding, the pedal or the lever stroke is too long, check that there are no leaks in

the braking system and if everything is OK, continue bleeding operations using the diag-

nostics instrument as described.

•

Detach the bleed hoses and close the bleed screws again to the correct tightening torque.

BLEEDING SYSTEM WITH DIAGNOSTICS INSTRUMENT

This type of bleeding has to be carried out if after all the checks the brake lever and the pedal

are still spongy.

The operations described here are valid for both systems even though the description refers to

the front system.

FRONT

•

With diagnostics instrument properly connected, select the function "FRONT BRAKE

BLEEDING PROCEDURE".

•

The pump starts rotating.

•

While the pump is performing a rotation cycle, operate and release the front brake lever until

the message diagnostics instrument cycle completion is received.

•

This procedure allows the air to turn and to accumulate.

•

Once the procedure with diagnostics instrument is finished, perform the REGULAR BLEED-

ING to remove the air from the system completely.

CAUTION

PERFORM THE REGULAR BRAKING SYSTEM BLEED, AS DESCRIBED AT THE BEGINNING OF
THE CHAPTER.

Braking system

CAPONORD 1200

BRAK SYS - 374

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands