APRILIA CAPONORD 1200 Service Station Manual Download Page 332

Page: 332 / 439

•

Replace both wheel bearings.

ALWAYS REPLACE BOTH BEARINGS.
ALWAYS REPLACE THE BEARINGS WITH OTHERS OF THE SAME TYPE.

•

Check the radial and axial clearance.

Axial clearance: a minimum axial clearance is allowed.

Radial clearance: none.

If one or both bearings do not fall within the control parameters:

•

Replace both wheel bearings.

REAR WHEEL GASKETS

•

Check that the gaskets are in good conditions; replace them if they show signs of damage

or excessive wear.

ALWAYS REPLACE BOTH GASKETS.
ALWAYS REPLACE THE GASKETS WITH OTHERS OF THE SAME TYPE.

REAR WHEEL AXLE

•

Use a dial gauge to check the wheel

axle eccentricity (1). Replace the

wheel axle if the eccentricity exceeds

the limit value (1).

Characteristic

Maximum eccentricity:

0.25 mm (0.0098 in)

REAR WHEEL RIM

•

Using a dial gauge, check that the ra-

dial (A) and the axial eccentricity (B) of

the rim (2) do not exceed the limit val-

ue.

An excessive eccentricity is usually caused by

worn or damaged bearings. Replace the rim (2) if

after replacing the bearings, the value is not within

the specified limit.

Characteristic

Maximum radial and axial eccentricity:

2 mm (0.0079 in)

Suspensions

CAPONORD 1200

SUSP - 332

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands