APRILIA CAPONORD 1200 Service Station Manual Download Page 279

Page: 279 / 439

CHECK THE ENGINE OIL FILTER O-RING.

LUBRICATION CHECK

•

Working on both crankcase halves, re-

move and thoroughly clean the nozzle

that lubricates the piston crown.

REPLACE THE SPRAY NOZZLE O-RING IF NECESSARY.

•

Replace the O-Rings on oil ducts.

Before refitting

UPON REFITTING THE CRANKSHAFT, GREASE THE SHAFT BUSHING-CONNECTING ROD
COUPLING.

CAPONORD 1200

Engine

ENG - 279

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands