APRILIA CAPONORD 1200 Service Station Manual Download Page 316

Page: 316 / 439

•

Fit the dust gaiter with the specific tool.

Specific tooling

AP8140189

Oil seal fitting tool for Ø 43 mm

(1.69 in) orifices

AP8140146

Weight

•

Insert the pumping member pin in the

stem.

•

Using a hook spanner lock the pump-

ing member pin and tighten the fixing

screw on the fork end to the prescribed

torque.

Specific tooling

020889Y

Pumping member ring nut locking

spanner

•

Insert the spring guide and lock it by the appropriate seeger.

•

Place the fork vertically.

•

Insert the washer.

Suspensions

CAPONORD 1200

SUSP - 316

Summary of Contents for CAPONORD 1200
























































































































































































































































































































































































































































Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands

APRILIA CAPONORD 1200, Service Station Manual

Search results

Summary of Contents for CAPONORD 1200

Reviews:

Related manuals for CAPONORD 1200

Brands by name

Popular brands